Research & Development

From theoretical synthesis to experimental validation.

The programme is built as a sequence of answerable questions, each with a defined method and a defined failure mode.

Can a low-mass planar four-bar mechanism produce a useful trailing-edge morphing law while maintaining acceptable transmission angle, actuator effort, structural stiffness and aerodynamic benefit?

Central research question

θ_TE θ_INPUT → MECHANISM → θ_TE

Conceptual schematic — the mechanism as a function generator.

Research workflow

Ten stages, each with a concrete output.

The sequence runs from requirements to validation. Theory precedes computation, and computation precedes hardware — no stage is skipped.

01

Requirements

Define morphing objectives, flight envelope, constraints and acceptance criteria.

02

Baseline geometry

Establish the NACA 2412 reference section and candidate UAV baseline planforms.

03

Mechanism synthesis

Synthesise a four-bar for the target trailing-edge deformation law.

04

Kinematic analysis

Solve position, velocity and acceleration; check transmission angle and singularities.

05

CAD integration

Package the linkage inside the section and integrate the morphing trailing edge.

06

CFD and FEA

Evaluate aerodynamic behaviour and structural response of the concept.

07

Optimization

Refine link geometry, stiffness and actuation effort within constraints.

08

Fabrication

Manufacture the demonstrator with conventional workshop processes.

09

Testing

Kinematic bench, static structural loading and aerodynamic demonstration.

10

Validation

Compare measured behaviour against simulation and document uncertainty.

Current position: stage 03 — mechanism synthesis and kinematic analysis. Stages 05 to 10 are planned work packages, not completed results.

Preliminary research

Two aerodynamic baselines, not two morphing states.

Two AERY32 baseline configurations were explored to understand what the mechanism must fit into. They are separate baseline designs studied side by side — not the same wing in different morphing positions.

Configuration A

ROOT SECTION TIP MODERATE SWEEP

Higher aspect ratio, cruise-oriented

A moderately swept baseline favouring induced-drag efficiency at cruise. Longer span means greater structural loading at the root and less spare volume for mechanism packaging.

Configuration B

ROOT SECTION TIP LOW SWEEP · COMPACT

Compact, low-sweep, low-speed

A shorter-span baseline suited to preliminary mechanism integration at low speed. Easier packaging and lower root loads, with a different induced-drag penalty to weigh.

Trade-offs under study

  • Aspect ratio versus structural load path — how far a span can be extended before root and spar sizing dominate the design.
  • Induced drag against mechanism packaging volume — thin, efficient sections leave little room for links and pivots.
  • Low-speed demonstrator practicality against cruise-representative aerodynamics.
  • Access, assembly and measurement provisions required by a first demonstrator.

Exploratory kinematics

MechSim studies shaped the mechanism, not just its drawing.

Exploratory four-bar studies examined offset pivots, alternative actuation arrangements, rocker motion and the trajectories traced through the working range.

What the studies examined

  • Offset pivot placement to keep the linkage inside the section envelope.
  • Alternative actuation arrangements and their effect on output range.
  • Rocker motion and the resulting trailing-edge rotation history.
  • Coupler trajectories as a check on interference and packaging.
  • Transmission angle behaviour across the intended input sweep.

These are exploratory simulations. Link dimensions, pivot coordinates and actuator placement are not published at this stage.

Tools in the programme

Fusion — CAD modelling and mechanism packaging In use
MechSim — Kinematic simulation and trajectory study In use
AERY32 — Baseline wing configuration studies In use
MATLAB — Analysis and engineering plots In use
ANSYS — Planned CFD and structural analysis Planned
Python — Potential optimization workflows Planned

Fabrication

The first demonstrator is built to teach, not to fly.

The initial hardware prioritises visible motion, repeatability, access and measurement. Flight readiness is explicitly out of scope for the first build — a demonstrator that can be measured is worth more than one that can only be photographed.

Processes available to the programme are conventional workshop processes, chosen for tolerance realism rather than novelty.

Laser cutting

Flat link plates and fixture plates with repeatable edges.

Power presses

Forming and blanking where a press is more practical than machining.

CNC bending

Repeatable sheet bends for brackets and mounting frames.

Additive manufacturing

Complex link housings and prototype trailing-edge segments.

Machining

Pivot bores, shafts and any interface needing tight tolerance.

Planned experimental validation

Three tests, in increasing order of difficulty.

Validation is planned, not performed. Each test is designed to answer a question the simulations cannot.

A Planned

Kinematic bench testing

Measure input angle against trailing-edge rotation on a rigid bench fixture. Establishes whether the realised mechanism follows the synthesised law.

B Planned

Static structural loading

Apply representative loads to the morphing segment and observe deflection and stiffness. Identifies whether the structure survives before any flow is introduced.

C Planned

Aerodynamic demonstration

Introduce flow and measure whether deformation produces measurable, repeatable change. The most demanding stage and the last in the plan.

Measurement uncertainty

Instrument resolution, fixture compliance and alignment error are recorded with every result.

Repeatability

Repeated sweeps establish whether the deformation law is stable or hysteresis-dominated.

Simulation-to-experiment

Measured behaviour is compared against the kinematic model, and differences are explained rather than smoothed over.

Research roadmap

Eight work packages, honestly labelled.

Statuses describe where each package stands. There are no invented progress percentages and no promised completion dates.

Intellectual property evaluation and commercialisation feasibility are long-term objectives, not current activity.

01 Ongoing

Research formulation and literature review

02 Preliminary work completed

Aerodynamic baseline and CAD modeling

03 In progress

Mechanism synthesis and kinematic analysis

04 Planned

Integrated mechanism and wing optimization

05 Planned

CFD and structural simulation

06 Planned

Physical demonstrator fabrication

07 Planned

Experimental aerodynamic validation

08 Long-term objective

Intellectual property evaluation and commercialization feasibility

Preliminary study

From simulation captures to a repeatable analysis workflow.

The October 2026 preliminary investigation brings together MechSim mechanism models, synchronized point-motion exports and derived kinematic analysis.

Record the motion

Screen recordings document mechanism motion and data collection. Public captures are available in the media gallery.

Analyse the response

The analysis workflow examines point trajectories, speed, acceleration, input–output rotation and transmission angle. The current geometry is provisional.

Define the next stage

Mechanism synthesis must connect a specified deformation requirement to packaging, actuation and structural constraints before aerodynamic benefit can be evaluated.

Reports, proposal slides, raw datasets and mechanism models remain private. Numerical simulation outputs are not validated flight results or actuator design loads.

View the original recordings